交换机做VRRP，上行的路由器也做VRRP应该怎么配置？

在学习VRRP部分时，遇到一个问题。
如果直连的交换机跟路由器同时配置VRRP的话，交换机到路由器的路由应该怎么过去呢

如图所示

img

在这种情况下 SW1配置了
sys
sys sw1

vlan 10 20 100

int g0/0/1
port link-type access
p d v 10

int g0/0/3
p l access
p d v 100

int g0/0/2
p l trunk
p trunk a v all

int vlanif 10
ip address 192.168.10.10 24
vrrp vrid 10 virtual-ip 192.168.10.254
vrrp vrid 10 p 105
vrrp vrid 10 track interface g0/0/3

int vlanif 20
ip address 192.168.20.10 24
vrrp vrid 20 virtual-ip 192.168.20.254
vrrp vrid 20 track interface g0/0/3

int vlanif 100
ip address 192.168.100.10 24
quit
ip route-s 20.0.0.0 24 192.168.100.254
ip route-s 10.0.0.0 24 192.168.200.254

SW2配置的是
sys
sys sw2

vlan 10 20 100

int g0/0/1
port link-type access
p d v 20

int g0/0/3
p l access
p d v 200

int g0/0/2
p l trunk
p trunk a v all

int vlanif 10
ip address 192.168.10.11 24
vrrp vrid 10 virtual-ip 192.168.10.254
vrrp vrid 10 track interface g0/0/3

int vlanif 20
ip address 192.168.20.11 24
vrrp vrid 20 virtual-ip 192.168.20.254
vrrp vrid 20 p 105
vrrp vrid 20 track interface g0/0/3

int vlanif 100
ip address 192.168.100.11 24
ip route-s 20.0.0.0 24 192.168.100.254
ip route-s 10.0.0.0 24 192.168.200.254

再往上走就不清楚了，我给R1配置了
sys
sys r1
int g0/0/1
ip address 192.168.100.100 24
vrrp vrid 100 virtual-ip 192.168.100.254
vrrp vrid 100 p 105
vrrp vrid 100 track interface g0/0/2

int g0/0/0
ip address 4.0.0.100 24

int g0/0/2
ip address 10.0.0.100 24

quit
ip route-s 3.3.3.3 32 10.0.0.254
ip route-s 3.3.3.3 32 4.0.0.101 p 65

R2则是sys
sys r2

int g0/0/0
ip address 192.168.100.101 24
vrrp vrid 100 virtual-ip 192.168.100.254
vrrp vrid 100 track interface g0/0/2

int g0/0/1
ip address 4.0.0.101 24

int g0/0/2
ip address 20.0.0.101 24

quit

ip route-s 3.3.3.3 32 20.0.0.254
ip route-s 3.3.3.3 32 4.0.0.100 p 65

这样不清楚如何生效 麻烦解惑解惑

你这个不该是lsw1在接一根线到AR2 lsw2在接一根线到AR1