linux WIFI 驱动调试
调试RK3566 + AP6256 的 WIFI 驱动出现问题。
在mmc_match_sdio() 执行时
第一次：SDIO 发送 CMD5 指令，参数0 时， 返回 OCR是： 0x30fF8000 (正常的开发板返回的是 0x30FfFf00)
第二次：SDIO 发送 CMD5 指令，参数0x1200000 时， 返回 OCR是： 0x30fF8000 (正常的开发板返回的是：0xb1FfFf00)
请问，那位知道，这个 sdio/IO 的wifi 驱动问题出在那里？？
[ 0.579037] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x2a, primary plane phy id: 5
[ 0.579062] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x15, primary plane phy id: 4
[ 0.579081] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[ 0.579503] [drm] unsupported AFBC format[3432564e]
[ 0.579748] rockchip-drm display-subsystem: bound fe040000.vop (ops vop2_component_ops)
[ 0.583238] panel-simple panel@0: Linked as a consumer to regulator.3
[ 0.583278] panel-simple panel@0: panel@0 supply vsp not found, using dummy regulator
[ 0.583329] panel-simple panel@0: Linked as a consumer to regulator.0
[ 0.583351] panel-simple panel@0: panel@0 supply vsn not found, using dummy regulator
[ 0.585115] mali fde60000.gpu: Kernel DDK version g7p1-01bet0
[ 0.585207] mali fde60000.gpu: Device initialization Deferred
[ 0.585330] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.590562] brd: module loaded
[ 0.602559] loop: module loaded
[ 0.602919] zram: Added device: zram0
[ 0.603215] SCSI Media Changer driver v0.25
[ 0.605455] libphy: Fixed MDIO Bus: probed
[ 0.605492] tun: Universal TUN/TAP device driver, 1.6
[ 0.606055] PPP generic driver version 2.4.2
[ 0.606196] PPP BSD Compression module registered
[ 0.606215] PPP Deflate Compression module registered
[ 0.606250] PPP MPPE Compression module registered
[ 0.606264] NET: Registered protocol family 24
[ 0.606290] PPTP driver version 0.8.5
[ 0.606559] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 0.606567] CSLIP: code copyright 1989 Regents of the University of California.
[ 0.606653] usbcore: registered new interface driver catc
[ 0.606710] usbcore: registered new interface driver kaweth
[ 0.606725] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 0.606772] usbcore: registered new interface driver pegasus
[ 0.606813] usbcore: registered new interface driver rtl8150
[ 0.606855] usbcore: registered new interface driver r8152
[ 0.606869] hso: drivers/net/usb/hso.c: Option Wireless
[ 0.606926] usbcore: registered new interface driver hso
[ 0.606967] usbcore: registered new interface driver asix
[ 0.607007] usbcore: registered new interface driver ax88179_178a
[ 0.607046] usbcore: registered new interface driver cdc_ether
[ 0.607089] usbcore: registered new interface driver cdc_eem
[ 0.607131] usbcore: registered new interface driver dm9601
[ 0.607174] usbcore: registered new interface driver smsc75xx
[ 0.607220] usbcore: registered new interface driver smsc95xx
[ 0.607254] usbcore: registered new interface driver gl620a
[ 0.607295] usbcore: registered new interface driver net1080
[ 0.607335] usbcore: registered new interface driver plusb
[ 0.607375] usbcore: registered new interface driver rndis_host
[ 0.607415] usbcore: registered new interface driver cdc_subset
[ 0.607459] usbcore: registered new interface driver zaurus
[ 0.607500] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 0.607545] usbcore: registered new interface driver int51x1
[ 0.607586] usbcore: registered new interface driver kalmia
[ 0.607626] usbcore: registered new interface driver ipheth
[ 0.607669] usbcore: registered new interface driver sierra_net
[ 0.607710] usbcore: registered new interface driver cx82310_eth
[ 0.607755] usbcore: registered new interface driver cdc_ncm
[ 0.607827] usbcore: registered new interface driver qmi_wwan
[ 0.607871] usbcore: registered new interface driver cdc_mbim
[ 0.608862] dwc3 fcc00000.dwc3: Failed to get clk 'ref': -2
[ 0.612768] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2
[ 0.614289] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.614308] ehci-pci: EHCI PCI platform driver
[ 0.614386] ehci-platform: EHCI generic platform driver
[ 0.616649] ehci-platform fd800000.usb: EHCI Host Controller
[ 0.616816] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[ 0.616954] ehci-platform fd800000.usb: irq 11, io mem 0xfd800000
[ 0.627820] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[ 0.627990] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.628007] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.628020] usb usb1: Product: EHCI Host Controller
[ 0.628033] usb usb1: Manufacturer: Linux 4.19.219 ehci_hcd
[ 0.628044] usb usb1: SerialNumber: fd800000.usb
[ 0.628419] hub 1-0:1.0: USB hub found
[ 0.628462] hub 1-0:1.0: 1 port detected
[ 0.630898] ehci-platform fd880000.usb: EHCI Host Controller
[ 0.631050] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[ 0.631186] ehci-platform fd880000.usb: irq 13, io mem 0xfd880000
[ 0.644496] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[ 0.644646] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19
[ 0.644663] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.644677] usb usb2: Product: EHCI Host Controller
[ 0.644689] usb usb2: Manufacturer: Linux 4.19.219 ehci_hcd
[ 0.644700] usb usb2: SerialNumber: fd880000.usb
[ 0.645032] hub 2-0:1.0: USB hub found
[ 0.645072] hub 2-0:1.0: 1 port detected
[ 0.645624] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.645654] ohci-platform: OHCI generic platform driver
[ 0.645856] ohci-platform fd840000.usb: Generic Platform OHCI controller
[ 0.646007] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[ 0.646130] ohci-platform fd840000.usb: irq 12, io mem 0xfd840000
[ 0.705288] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 0.705305] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.705319] usb usb3: Product: Generic Platform OHCI controller
[ 0.705331] usb usb3: Manufacturer: Linux 4.19.219 ohci_hcd
[ 0.705343] usb usb3: SerialNumber: fd840000.usb
[ 0.705685] hub 3-0:1.0: USB hub found
[ 0.705726] hub 3-0:1.0: 1 port detected
[ 0.706102] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[ 0.706265] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[ 0.706398] ohci-platform fd8c0000.usb: irq 14, io mem 0xfd8c0000
[ 0.765289] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 4.19
[ 0.765307] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.765320] usb usb4: Product: Generic Platform OHCI controller
[ 0.765333] usb usb4: Manufacturer: Linux 4.19.219 ohci_hcd
[ 0.765344] usb usb4: SerialNumber: fd8c0000.usb
[ 0.765685] hub 4-0:1.0: USB hub found
[ 0.765725] hub 4-0:1.0: 1 port detected
[ 0.766876] usbcore: registered new interface driver cdc_acm
[ 0.766894] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 0.766963] usbcore: registered new interface driver usblp
[ 0.767022] usbcore: registered new interface driver cdc_wdm
[ 0.767259] usbcore: registered new interface driver uas
[ 0.767333] usbcore: registered new interface driver usb-storage
[ 0.767377] usbcore: registered new interface driver ums-alauda
[ 0.767420] usbcore: registered new interface driver ums-cypress
[ 0.767463] usbcore: registered new interface driver ums-datafab
[ 0.767505] usbcore: registered new interface driver ums_eneub6250
[ 0.767547] usbcore: registered new interface driver ums-freecom
[ 0.767594] usbcore: registered new interface driver ums-isd200
[ 0.767636] usbcore: registered new interface driver ums-jumpshot
[ 0.767676] usbcore: registered new interface driver ums-karma
[ 0.767719] usbcore: registered new interface driver ums-onetouch
[ 0.767754] usbcore: registered new interface driver ums-sddr09
[ 0.767829] usbcore: registered new interface driver ums-sddr55
[ 0.767873] usbcore: registered new interface driver ums-usbat
[ 0.767964] usbcore: registered new interface driver usbserial_generic
[ 0.767995] usbserial: USB Serial support registered for generic
[ 0.768040] usbcore: registered new interface driver option
[ 0.768067] usbserial: USB Serial support registered for GSM modem (1-port)
[ 0.768174] usbcore: registered new interface driver trancevibrator
[ 0.768709] usbcore: registered new interface driver xpad
[ 0.768763] usbcore: registered new interface driver usb_acecad
[ 0.768809] usbcore: registered new interface driver aiptek
[ 0.768854] usbcore: registered new interface driver gtco
[ 0.768903] usbcore: registered new interface driver hanwang
[ 0.768949] usbcore: registered new interface driver kbtab
[ 0.769056] <<-GTP-INFO->> GTP driver installing...
[ 0.769282] cyttsp5_loader_init: Parade TTSP FW Loader Driver (Built TTDA.03.08.874312) rc=0
[ 0.769292] cyttsp5_device_access_init: Parade TTSP Device Access Driver (Built TTDA.03.08.874312) rc=0
[ 0.770402] i2c /dev entries driver
[ 0.772153] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected!
[ 0.773890] vdd_cpu: supplied by vcc3v8_sys
[ 0.778495] rk808 0-0020: chip id: 0x8170
[ 0.778538] rk808 0-0020: No cache defaults, reading back from HW
[ 0.802189] rk808 0-0020: source: on=0x10, off=0x00
[ 0.802209] rk808 0-0020: support dcdc3 fb mode:-22, 0
[ 0.802223] rk808 0-0020: support pmic reset mode:0,0
[ 0.807216] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 0.807254] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 0.807667] vdd_logic: supplied by vcc3v8_sys
[ 0.808352] vdd_gpu: supplied by vcc3v8_sys
[ 0.808581] vcc_ddr: supplied by vcc3v8_sys
[ 0.808805] vcc_3v3: supplied by vcc3v8_sys
[ 0.809027] vcca1v8_pmu: supplied by vcc3v8_sys
[ 0.809581] vdda_0v9: supplied by vcc3v8_sys
[ 0.809804] vdda0v9_pmu: supplied by vcc3v8_sys
[ 0.810022] vccio_acodec: supplied by vcc3v8_sys
[ 0.810567] vccio_sd: supplied by vcc3v8_sys
[ 0.811134] vcc3v3_pmu: supplied by vcc3v8_sys
[ 0.811713] vcc_1v8: supplied by vcc3v8_sys
[ 0.811938] vcc1v8_dvp: supplied by vcc3v8_sys
[ 0.812153] vcc2v8_dvp: supplied by vcc3v8_sys
[ 0.812365] boost: Bringing 4700000uV into 5000000-5000000uV
[ 0.812725] boost: supplied by vcc3v8_sys
[ 0.813886] otg_switch: supplied by boost
[ 0.814139] rk817-battery rk817-battery: DMA mask not set
[ 0.814248] rk817-battery rk817-battery: fb_temperature missing!
[ 0.814265] rk817-battery rk817-battery: energy_mode missing!
[ 0.814279] rk817-battery rk817-battery: zero_reserve_dsoc missing!
[ 0.814759] rk817-battery rk817-battery: low_power_sleep missing!
[ 0.838665] rk817-bat: initialized yet..
[ 0.885524] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[ 0.885756] rk817-charger rk817-charger: DMA mask not set
[ 0.885816] rk817-charger rk817-charger: power_dc2otg missing!
[ 0.885832] rk817-charger rk817-charger: sample_res missing!
[ 0.885845] rk817-charger rk817-charger: otg5v_suspend_enable missing!
[ 0.885858] rk817-charger rk817-charger: gate_function_disable missing!
[ 0.886397] rk817-charger rk817-charger: Linked as a consumer to regulator.20
[ 0.895725] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input0
[ 0.901757] rk808-rtc rk808-rtc: registered as rtc0
[ 0.903465] rk808-rtc rk808-rtc: setting system clock to 2022-07-01 16:37:18 UTC (1656693438)
[ 0.905623] <<-GTP-INFO->> >>>>>>>>>>>>>>>>> GTP Driver Version: V2.4<2014/11/28>
[ 0.905644] <<-GTP-INFO->> GTP I2C Address: 0x5d
[ 0.905734] <<-GTP-INFO->> Guitar reset
[ 1.011425] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[ 1.011440] <<-GTP-INFO->> Guitar reset
[ 1.107805] <<-GTP-ERROR->> GTP i2c test failed time 1.
[ 1.124748] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[ 1.124763] <<-GTP-INFO->> Guitar reset
[ 1.221138] <<-GTP-ERROR->> GTP i2c test failed time 2.
[ 1.238081] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[ 1.238095] <<-GTP-INFO->> Guitar reset
[ 1.334470] <<-GTP-ERROR->> GTP i2c test failed time 3.
[ 1.351414] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[ 1.351429] <<-GTP-INFO->> Guitar reset
[ 1.447804] <<-GTP-ERROR->> GTP i2c test failed time 4.
[ 1.464751] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[ 1.464765] <<-GTP-INFO->> Guitar reset
[ 1.561184] <<-GTP-ERROR->> GTP i2c test failed time 5.
[ 1.577806] <<-GTP-ERROR->> I2C communication ERROR!
[ 1.579613] iommu: Adding device fdff0000.rkisp to group 5
[ 1.579647] rkisp_hw fdff0000.rkisp: Linked as a consumer to fdff1a00.iommu
[ 1.579806] rkisp_hw fdff0000.rkisp: is_thunderboot: 0
[ 1.579824] rkisp_hw fdff0000.rkisp: max input:0x0@0fps
[ 1.579850] rkisp_hw fdff0000.rkisp: can't request region for resource [mem 0xfdff0000-0xfdffffff]
[ 1.580451] rkisp rkisp-vir0: rkisp driver version: v01.07.00
[ 1.580535] rkisp rkisp-vir0: No memory-region-thunderboot specified
[ 1.580725] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[ 1.580749] rkisp rkisp-vir0: Entity type for entity rkisp-csi-subdev was not initialized!
[ 1.582289] usbcore: registered new interface driver uvcvideo
[ 1.582307] USB Video Class driver (1.1.1)
[ 1.582535] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.15
[ 1.582567] rockchip-iodomain fdc20000.syscon:io-domains: pmuio1(3300000 uV) supplied by vcc3v3_pmu
[ 1.582645] rockchip-iodomain fdc20000.syscon:io-domains: pmuio2(3300000 uV) supplied by vcc3v3_pmu
[ 1.582712] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.13
[ 1.582738] rockchip-iodomain fdc20000.syscon:io-domains: vccio1(3300000 uV) supplied by vccio_acodec
[ 1.582841] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.14
[ 1.582867] rockchip-iodomain fdc20000.syscon:io-domains: vccio3(3300000 uV) supplied by vccio_sd
[ 1.582936] rockchip-iodomain fdc20000.syscon:io-domains: vccio4(3300000 uV) supplied by vcc3v3_pmu
[ 1.583005] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.9
[ 1.583032] rockchip-iodomain fdc20000.syscon:io-domains: vccio5(3300000 uV) supplied by vcc_3v3
[ 1.583112] rockchip-iodomain fdc20000.syscon:io-domains: Linked as a consumer to regulator.17
[ 1.583139] rockchip-iodomain fdc20000.syscon:io-domains: vccio6(1800000 uV) supplied by vcc1v8_dvp
[ 1.583208] rockchip-iodomain fdc20000.syscon:io-domains: vccio7(3300000 uV) supplied by vcc_3v3
[ 1.584342] test_power_init: could not find dev node
[ 1.585797] rockchip-thermal fe710000.tsadc: tsadc is probed successfully!
[ 1.586676] device-mapper: uevent: version 1.0.3
[ 1.586894] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
[ 1.587085] device-mapper: verity-avb: AVB error handler initialized with vbmeta device:
[ 1.587105] Bluetooth: HCI UART driver ver 2.3
[ 1.587120] Bluetooth: HCI UART protocol H4 registered
[ 1.587360] cpu cpu0: leakage=53
[ 1.587410] cpu cpu0: pvtm = 93510, from nvmem
[ 1.587429] cpu cpu0: pvtm-volt-sel=2
[ 1.588183] cpu cpu0: Linked as a consumer to regulator.5
[ 1.588231] cpu cpu0: Dropping the link to regulator.5
[ 1.588824] cpu cpu0: Linked as a consumer to regulator.5
[ 1.589417] cpu cpu0: avs=0
[ 1.589469] energy_model: pd0: hertz/watts ratio non-monotonically decreasing: em_cap_state 2 >= em_cap_state1
[ 1.589656] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 1.592990] cpu cpu0: failed to find power_model node
[ 1.593674] WCKJ >>>>>>>>>>>>>>>. mmc_pwrseq_simple_probe
[ 1.594159] sdhci: Secure Digital Host Controller Interface driver
[ 1.594175] sdhci: Copyright(c) Pierre Ossman
[ 1.594188] Synopsys Designware Multimedia Card Interface Driver
[ 1.594935] wckj >>>>>>>>>>>>>>> dw_mci_rockchip_probe
[ 1.595171] dwmmc_rockchip fe2b0000.dwmmc: IDMAC supports 32-bit address mode.
[ 1.595225] dwmmc_rockchip fe2b0000.dwmmc: Using internal DMA controller.
[ 1.595244] dwmmc_rockchip fe2b0000.dwmmc: Version ID is 270a
[ 1.595295] dwmmc_rockchip fe2b0000.dwmmc: DW MMC controller at irq 38,32 bit host data width,256 deep fifo
[ 1.595390] dwmmc_rockchip fe2b0000.dwmmc: Linked as a consumer to regulator.4
[ 1.595456] dwmmc_rockchip fe2b0000.dwmmc: Linked as a consumer to regulator.14
[ 1.595657] wckj >>>>>>>>>>>> (mmc0) Initial signal voltage of 3.3v
[ 1.608307] mmc_host mmc0: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 1.621281] wckj >>>>>>>>>>>>>>> dw_mci_rockchip_probe
[ 1.621474] dwmmc_rockchip fe2c0000.dwmmc: IDMAC supports 32-bit address mode.
[ 1.621534] dwmmc_rockchip fe2c0000.dwmmc: Using internal DMA controller.
[ 1.621552] dwmmc_rockchip fe2c0000.dwmmc: Version ID is 270a
[ 1.621601] dwmmc_rockchip fe2c0000.dwmmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo
[ 1.621711] dwmmc_rockchip fe2c0000.dwmmc: allocated mmc-pwrseq
[ 1.621730] mmc_host mmc1: card is non-removable.
[ 1.621852] wckj >>>>> PRE POWER ON <<<<<<<<< mmc_pwrseq_simple_pre_power_on
[ 1.621883] wckj >>>>>>>>>>>> (mmc1) Initial signal voltage of 3.3v
[ 1.634456] wckj >>>>> POST POWER ON <<<<<<<<< mmc_pwrseq_simple_post_power_on
[ 1.842207] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[ 1.855032] wckj >>>>>>>>>>>>>>>>> mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
[ 1.855639] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.858935] mmc2: Unknown controller version (5). You may experience problems.
[ 1.862461] wckj >>>>>>>>>>>>>>> mmc_attach_sdio
[ 1.862531] wckj >>>>>>>>>>>>>>> mmc_attach_sdio (1145)
[ 1.862574] wckj start: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (0x5:0x0)
[ 1.863054] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0)
[ 1.863070] wckj stop: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (rocr: 0x30ff8000)
[ 1.863081] wckj ###########(mmc1) ocr: 0x30ff8000
[ 1.863094] wckj ###### ocr: 30ff8000 ocr->avail: 300000
[ 1.863106] wckj ######### mmc_attach_sdio >> mmc_select_voltage SUCC(0x200000) !!!
[ 1.863118] wckj >>>>>>>>>>> mmc_sdio_init_card (orc: 0x200000) ##### start
[ 1.863130] (null): >>>> retries: 18874368 ocr: 0x0 alive: 0x0
[ 1.863140] wckj start: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (0x5:0x1200000)
[ 1.863524] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 1.863541] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 1.865958] wckj >>>>>>>>>>>> (mmc2) Initial signal voltage of 3.3v
[ 1.876477] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 1.876493] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 1.889440] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 1.889456] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 1.891164] wckj >>>>>>>>>>>>>>>>> mmc2: mmc_rescan_try_freq: trying to init card at 400000 Hz
[ 1.891200] mmc2: SDHCI controller on fe310000.sdhci [fe310000.sdhci] using ADMA
[ 1.891971] rgb13h-flash flash-rgb13h: driver version: 00.01.01
[ 1.892032] of_pwm_get(): can't parse "pwms" property
[ 1.892049] rgb13h-flash flash-rgb13h: Unable to get pwm device
[ 1.892654] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.901621] usbcore: registered new interface driver usbhid
[ 1.901651] usbhid: USB HID core driver
[ 1.901730] ion_device_add_heap: ion_system_contig_heap id=0 type=1
[ 1.901760] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 1.901783] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 1.902117] ion_device_add_heap: ion_system_heap id=1 type=0
[ 1.902141] ion_device_add_heap: linux,cma id=2 type=4
[ 1.902533] ashmem: initialized
[ 1.902897] rockchip,bus bus-npu: Linked as a consumer to regulator.6
[ 1.902927] rockchip,bus bus-npu: Failed to get leakage
[ 1.902994] rockchip,bus bus-npu: pvtm = 93510, from nvmem
[ 1.903018] rockchip,bus bus-npu: pvtm-volt-sel=2
[ 1.903359] rockchip,bus bus-npu: avs=0
[ 1.906647] rockchip-saradc fe720000.saradc: Linked as a consumer to regulator.16
[ 1.907230] optee: probing for conduit method from DT.
[ 1.907264] optee: revision 3.13 (f5add58b)
[ 1.907701] optee: initialized driver
[ 1.907731] rknandbase v1.2 2021-01-07
[ 1.908350] rknand fe330000.nandc: rknand_probe clk rate = 148500000
[ 1.914758] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 1.914774] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 1.924596] mmc2: new HS200 MMC card at address 0001
[ 1.925433] mmcblk2: mmc2:0001 DA6016 14.7 GiB
[ 1.926052] mmcblk2boot0: mmc2:0001 DA6016 partition 1 4.00 MiB
[ 1.926869] mmcblk2boot1: mmc2:0001 DA6016 partition 2 4.00 MiB
[ 1.927156] mmcblk2rpmb: mmc2:0001 DA6016 partition 3 4.00 MiB, chardev (237:0)
[ 1.927734] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 1.927749] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 1.930806] mmcblk2: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14
[ 1.938152] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.722463] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.722475] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.732093] ftl_init fffffffe
[ 2.732104] rk_ftl_init fail
[ 2.732448] wckj >>>>>>>>>>>>>>>>>>> wckj_power_probe
[ 2.732462] wckj_power prepare build 2 gpio
[ 2.732496] wckj_power request usb_host1
[ 2.732520] success request gpio148 out
[ 2.732537] wckj_power request usb_host2
[ 2.732549] success request gpio149 out
[ 2.732659] input: gpio_event as /devices/platform/wckj_power/input/input1
[ 2.732857] rpdzkj wake lock
[ 2.733206] usbcore: registered new interface driver snd-usb-audio
[ 2.734435] rk817-codec rk817-codec: DMA mask not set
[ 2.734921] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.734937] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.738371] netem: version 1.3
[ 2.738396] u32 classifier
[ 2.738404] Actions configured
[ 2.738894] xt_time: kernel timezone is -0000
[ 2.738976] gre: GRE over IPv4 demultiplexor driver
[ 2.738986] IPv4 over IPsec tunneling driver
[ 2.739505] Initializing XFRM netlink socket
[ 2.739531] IPsec XFRM device driver
[ 2.739796] NET: Registered protocol family 10
[ 2.740625] Segment Routing with IPv6
[ 2.740693] mip6: Mobile IPv6
[ 2.741182] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.741728] NET: Registered protocol family 17
[ 2.741753] NET: Registered protocol family 15
[ 2.741805] Bridge firewalling registered
[ 2.742116] Bluetooth: RFCOMM TTY layer initialized
[ 2.742148] Bluetooth: RFCOMM socket layer initialized
[ 2.742179] Bluetooth: RFCOMM ver 1.11
[ 2.742199] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 2.742208] Bluetooth: BNEP filters: protocol multicast
[ 2.742221] Bluetooth: BNEP socket layer initialized
[ 2.742230] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.742239] Bluetooth: HIDP socket layer initialized
[ 2.742268] l2tp_core: L2TP core driver, V2.0
[ 2.742283] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 2.742293] [BT_RFKILL]: Enter rfkill_rk_init
[ 2.742300] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 2.742731] [WLAN_RFKILL]: wckj >>>>>> Enter rfkill_wlan_probe
[ 2.742767] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ''
[ 2.742777] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 2.742786] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 2.742816] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 20, flags = 0.
[ 2.742829] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 2.742837] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 2.742848] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[ 2.742856] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 2.743317] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 77.
[ 2.743342] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 17.
[ 2.743353] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 14.
[ 2.743367] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 13.
[ 2.743416] [BT_RFKILL]: Request irq for bt wakeup host
[ 2.743485] [BT_RFKILL]: ** disable irq
[ 2.743595] [BT_RFKILL]: bt_default device registered.
[ 2.745034] registered taskstats version 1
[ 2.745051] Loading compiled-in X.509 certificates
[ 2.745152] Key type ._fscrypt registered
[ 2.745164] Key type .fscrypt registered
[ 2.745173] Key type fscrypt-provisioning registered
[ 2.745452] pstore: Using compression: deflate
[ 2.746389] rga2: Driver loaded successfully ver:3.2.63318
[ 2.746634] rga2: Module initialized.
[ 2.747857] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.747879] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.760755] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.760785] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.764665] vendor storage:20190527 ret = 0
[ 2.769751] rockchip-drm display-subsystem: defer getting devfreq
[ 2.770025] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x2a, primary plane phy id: 5
[ 2.770045] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x15, primary plane phy id: 4
[ 2.770059] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[ 2.770573] rockchip-drm display-subsystem: bound fe040000.vop (ops vop2_component_ops)
[ 2.770613] rockchip-drm display-subsystem: bound fdc60000.syscon:lvds (ops rockchip_lvds_component_ops)
[ 2.770771] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 2.771508] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.771528] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.771926] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[ 2.773757] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops dw_hdmi_rockchip_ops)
[ 2.773788] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.773800] [drm] No driver support for vblank timestamp query.
[ 2.774176] get_framebuffer_by_node: failed to get logo,offset
[ 2.774256] rockchip-drm display-subsystem: connector[HDMI-A-1] can't found any modes
[ 2.783522] rockchip-drm display-subsystem: fb0: frame buffer device
[ 2.784296] [drm] Initialized rockchip 2.0.0 20140818 for display-subsystem on minor 0
[ 2.784417] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.784428] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.785190] mali fde60000.gpu: Kernel DDK version g7p1-01bet0
[ 2.785366] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2
[ 2.785372] mali fde60000.gpu: Linked as a consumer to regulator.7
[ 2.785515] mali fde60000.gpu: dev_pm_opp_set_regulators: no regulator (shadercores) found: -19
[ 2.785614] mali fde60000.gpu: leakage=12
[ 2.785665] mali fde60000.gpu: pvtm = 93510, from nvmem
[ 2.786019] input: adc-keys as /devices/platform/adc-keys/input/input2
[ 2.786139] mali fde60000.gpu: avs=0
[ 2.786164] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 112; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[ 2.786480] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
[ 2.786565] mali fde60000.gpu: No priority control manager is configured
[ 2.786584] mali fde60000.gpu: No memory group manager is configured
[ 2.786640] rockchip-dmc dmc: Linked as a consumer to regulator.6
[ 2.786754] rockchip-dmc dmc: leakage=81
[ 2.786783] rockchip-dmc dmc: leakage-volt-sel=1
[ 2.786841] rockchip-dmc dmc: pvtm = 93510, from nvmem
[ 2.786861] rockchip-dmc dmc: pvtm-volt-sel=1
[ 2.787095] rockchip-dmc dmc: avs=0
[ 2.787119] rockchip-dmc dmc: current ATF version 0x101
[ 2.787242] mali fde60000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[ 2.788157] mali fde60000.gpu: Probed as mali0
[ 2.788256] rockchip-dmc dmc: normal_rate = 780000000
[ 2.788276] rockchip-dmc dmc: reboot_rate = 1056000000
[ 2.788291] rockchip-dmc dmc: suspend_rate = 324000000
[ 2.788304] rockchip-dmc dmc: video_4k_rate = 780000000
[ 2.788316] rockchip-dmconsole:/ $ dmc: video_4k_10b_rate = 780000000
[ 2.788327] rockchip-dmc dmc: boost_rate = 1056000000
[ 2.788339] rockchip-dmc dmc: fixed_rate(isp|cif0|cif1|dualview) = 1056000000
[ 2.788350] rockchip-dmc dmc: performance_rate = 1056000000
[ 2.788376] rockchip-dmc dmc: failed to get vop pn to msch rl
[ 2.788526] rockchip-dmc dmc: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[ 2.788574] rockchip-dmc dmc: could not find power_model node
[ 2.797334] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.797349] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.800002] asoc-simple-card hdmi-sound: i2s-hifi <-> fe400000.i2s mapping ok
[ 2.806481] asoc-simple-card rk817-sound: rk817-hifi <-> fe410000.i2s mapping ok
[ 2.808161] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2
[ 2.808244] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.808260] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.809671] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2
[ 2.813447] It doesn't contain Rogue gpu
[ 2.814648] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 2.815779] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 2.815976] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 2.815998] cfg80211: failed to load regulatory.db
[ 2.817929] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[ 2.818640] dwc3 fd000000.dwc3: Failed to get clk 'ref': -2
[ 2.819973] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '00:02:51'.
[ 2.820550] Mali:
[ 2.820553] Mali device driver loaded
[ 2.820587] rkisp rkisp-vir0: clear unready subdev num: 2
[ 2.820604] rockchip-csi2-dphy0: No link between dphy and sensor
[ 2.821233] rockchip-csi2-dphy0: No link between dphy and sensor
[ 2.821248] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.821252] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.821259] rkisp-vir0: update sensor failed
[ 2.821559] ALSA device list:
[ 2.821571] #0: rockchip,hdmi
[ 2.821580] #1: rockchip,rk817-codec
[ 2.827131] Freeing unused kernel memory: 3968K
[ 2.827300] Run /init as init process
[ 2.831445] init: init first stage started!
[ 2.831734] init: Unable to open /lib/modules, skipping module loading.
[ 2.832259] init: [libfs_mgr]ReadFstabFromDt(): failed to read fstab from dt
[ 2.834189] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.834210] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.834281] init: Using Android DT directory /proc/device-tree/firmware/android/
[ 2.844979] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.845023] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.858041] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.858086] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.871012] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.871054] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.881728] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.881776] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.884939] init: [libfs_mgr]superblock s_max_mnt_count:65535,/dev/block/by-name/metadata
[ 2.885175] init: [libfs_mgr]Filesystem on /dev/block/by-name/metadata was not cleanly shutdown; state flags: 0x1, incompat featureI/TA: Hello Rockchip Keymaster! rpmb :0
flags: 0x46
[ 2.885389] init: [libfs_mgr]check_fs(): mount(/dev/block/by-name/metadata,/metadata,ext4)=-1: No such file or directory
[ 2.885602] init: [libfs_mgr]Not running /system/bin/e2fsck on /dev/block/mmcblk2p11 (executable not in system image)
[ 2.889414] devfreq fde60000.gpu: Couldn't update frequency transition information.
[ 2.893010] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.893047] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.893206] EXT4-fs (mmcblk2p11): recovery complete
[ 2.893992] EXT4-fs (mmcblk2p11): mounted filesystem with ordered data mode. Opts: discard
[ 2.894354] init: [libfs_mgr]__mount(source=/dev/block/by-name/metadata,target=/metadata,type=ext4)=0: Success
[ 2.896285] init: Failed to copy /avb into /metadata/gsi/dsu/avb/: No such file or directory
[ 2.904926] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.904970] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.914597] EXT4-fs (dm-0): mounted filesystem without journal. Opts: barrier=1
[ 2.917877] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.917931] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.924618] EXT4-fs (dm-2): mounted filesystem without journal. Opts: barrier=1
[ 2.929562] EXT4-fs (dm-4): mounted filesystem without journal. Opts: barrier=1
[ 2.930850] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.930881] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.935533] EXT4-fs (dm-3): mounted filesystem without journal. Opts: barrier=1
[ 2.940700] EXT4-fs (dm-1): mounted filesystem without journal. Opts: barrier=1
[ 2.941569] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.941601] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.954564] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 2.954607] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 2.966711] init: 18 output lines suppressed due to ratelimiting
[ 3.116270] init: Loading SELinux policy
[ 3.124674] wckj stop: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (rocr: 0x30ff8000)
[ 3.124722] wckj $$$$$$$$$$$$$$$$$ mmc_sdio_init_card: mmc_send_io_op_cond() err=-110
[ 3.124729] mmc_sdio_init_card: >>>>>>>>>>> ERR !!!
[ 3.124738] wckj ######### mmc_attach_sdio >> mmc_sdio_init_card ERR !!!
[ 3.124748] mmc1: error -110 whilst initialising SDIO card
[ 3.124760] wckj >>>>> POWER OFF <<<<<<<<< mmc_pwrseq_simple_power_off
[ 3.125985] wckj >>>>>>>>>>>>>>>>> mmc1: mmc_rescan_try_freq: trying to init card at 300000 Hz
[ 3.126012] wckj >>>>> PRE POWER ON <<<<<<<<< mmc_pwrseq_simple_pre_power_on
[ 3.126046] wckj >>>>>>>>>>>> (mmc1) Initial signal voltage of 3.3v
[ 3.138008] wckj >>>>> POST POWER ON <<<<<<<<< mmc_pwrseq_simple_post_power_on
[ 3.151720] SELinux: Permission nlmsg_getneigh in class netlink_route_socket not defined in policy.
[ 3.152134] SELinux: the above unknown classes and permissions will be denied
[ 3.152236] SELinux: policy capability network_peer_controls=1
[ 3.152250] SELinux: policy capability open_perms=1
[ 3.152262] SELinux: policy capability extended_socket_class=1
[ 3.152274] SELinux: policy capability always_check_network=0
[ 3.152285] SELinux: policy capability cgroup_seclabel=0
[ 3.152297] SELinux: policy capability nnp_nosuid_transition=1
[ 3.309481] audit: type=1403 audit(1656693440.903:2): auid=4294967295 ses=4294967295 lsm=selinux res=1
[ 3.309796] selinux: SELinux: Loaded policy from /odm/etc/selinux/precompiled_sepolicy
[ 3.309829] selinux:
[ 3.310874] audit: type=1404 audit(1656693440.903:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295 enabled=1 old-enabled=1 lsm=selinux res=1
[ 3.333354] selinux: SELinux: Loaded file_contexts
[ 3.333451] selinux:
[ 3.344622] mmc_host mmc1: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[ 3.364413] wckj >>>>>>>>>>>>>>> mmc_attach_sdio
[ 3.364504] wckj >>>>>>>>>>>>>>> mmc_attach_sdio (1145)
[ 3.364525] wckj start: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (0x5:0x0)
[ 3.364936] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0)
[ 3.364955] wckj stop: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (rocr: 0x30ff8000)
[ 3.364970] wckj ###########(mmc1) ocr: 0x30ff8000
[ 3.364982] wckj ###### ocr: 30ff8000 ocr->avail: 300000
[ 3.364994] wckj ######### mmc_attach_sdio >> mmc_select_voltage SUCC(0x200000) !!!
[ 3.365006] wckj >>>>>>>>>>> mmc_sdio_init_card (orc: 0x200000) ##### start
[ 3.365018] (null): >>>> retries: 18874368 ocr: 0x0 alive: 0x0
[ 3.365033] wckj start: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (0x5:0x1200000)
[ 3.365421] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 3.365438] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 3.378360] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 3.378404] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 3.380115] init: init second stage started!
[ 3.438866] init: Using Android DT directory /proc/device-tree/firmware/android/
[ 3.440537] init: Init cannot set 'ro.boot.verifiedbootstate' to 'orange': Read-only property was already set
[ 3.441460] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 3.441493] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 3.445580] init: Overriding previous 'ro.' property 'pm.dexopt.shared':'speed' with new value 'quicken'
[ 3.448545] init: Do not have permissions to set 'ro.flash_img.enable' to 'false' in property file '/vendor/default.prop': SELinux permission check failed
[ 3.450382] init: Do not have permissions to set 'ro.product.ota.host' to 'www.rockchip.com:2300' in property file '/vendor/build.prop': SELinux permission check failed
[ 3.450690] init: Do not have permissions to set 'ro.ril.ecclist' to '112,911' in property file '/vendor/build.prop': SELinux permission check failed
[ 3.450933] init: Do not have permissions to set 'sys.wallpaper.rgb565' to '0' in property file '/vendor/build.prop': SELinux permission check failed
[ 3.451028] init: Do not have permissions to set 'sys.rkadb.root' to '0' in property file '/vendor/build.prop': SELinux permission check failed
[ 3.451108] init: Do not have permissions to set 'ro.sf.fakerotation' to 'false' in property file '/vendor/build.prop': SELinux permission check failed
[ 3.454516] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 3.454552] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 3.467680] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 3.525082] audit: type=1107 audit(1656693441.120:4): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg='avc: denied { read } for property=persist.sys.adb_enable pid=0 uid=0 gid=0 scontext=u:r'
[ 3.525567] audit: type=1107 audit(1656693441.120:5): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg='avc: denied { read } for property=persist.sys.adb_enable pid=0 uid=0 gid=0 scontext=u:r'
[ 3.525878] audit: type=1107 audit(1656693441.120:6): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg='avc: denied { read } for property=persist.sys.read_pcie_info pid=0 uid=0 gid=0 scontext'
[ 3.526491] audit: type=1107 audit(1656693441.120:7): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg='avc: denied { read } for property=flash.success pid=0 uid=0 gid=0 scontext=u:r:vendor_i'
[ 3.528260] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 3.528304] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 3.531992] audit: type=1107 audit(1656693441.126:8): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg='avc: denied { read } for property=init.svc.adbd pid=0 uid=0 gid=0 scontext=u:r:vendor_i'
[ 3.541341] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 3.541394] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 3.617712] cgroup: init (1) created nested cgroup for controller "memory" which has incomplete hierarchy support. Nested cgroups may change behavior in the future.
[ 3.617766] cgroup: "memory" requires setting use_hierarchy to 1 on the root
[ 3.627854] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 3.627900] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 3.721439] ueventd: ueventd started!
[ 3.725585] selinux: SELinux: Loaded file_contexts
[ 3.725654] selinux:
[ 3.726432] ueventd: Parsing file /system/etc/ueventd.rc...
[ 3.727414] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 3.727444] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 3.728207] ueventd: Parsing file /vendor/ueventd.rc...
[ 3.730618] ueventd: Parsing file /odm/ueventd.rc...
[ 3.730815] ueventd: Unable to read config file '/odm/ueventd.rc': open() failed: No such file or directory
[ 3.730935] ueventd: Parsing file /ueventd.rk30board.rc...
[ 3.731013] ueventd: Unable to read config file '/ueventd.rk30board.rc': open() failed: No such file or directory
[ 3.774020] apexd: This device does not support updatable APEX. Exiting
[ 4.161093] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 4.161140] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 4.533809] EXT4-fs (mmcblk2p10): Ignoring removed nomblk_io_submit option
[ 4.540779] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 4.540810] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 4.543913] logd.auditd: start
[ 4.543973] logd.klogd: 4392847615
[ 4.547724] EXT4-fs (mmcblk2p10): recovery complete
[ 4.551515] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 4.551539] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 4.554383] EXT4-fs (mmcblk2p10): mounted filesystem with ordered data mode. Opts: errors=remount-ro,nomblk_io_submit
[ 4.562492] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 4.562520] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 4.574906] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 4.574935] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 4.587357] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 4.587391] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 4.592876] type=1107 audit(1656693442.146:9): uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg='avc: denied { set } for property=persist.vendor.rknn.log.level pid=139 uid=0 gid=0 scontext=u:r:rknn_s'
[ 4.593214] type=1107 audit(1656693442.146:10): uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg='avc: denied { set } for property=persist.vendor.rknn.dump.quant pid=139 uid=0 gid=0 scontext=u:r:rknn'
[ 4.593544] type=1107 audit(1656693442.146:11): uid=0 auid=4294967295 ses=4294967295 subj=u:r:init:s0 msg='avc: denied { set } for property=persist.vendor.rknn.dump.dir pid=139 uid=0 gid=0 scontext=u:r:rknn_s'
[ 4.598656] wckj stop: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (rocr: 0x30ff8000)
[ 4.598687] wckj $$$$$$$$$$$$$$$$$ mmc_sdio_init_card: mmc_send_io_op_cond() err=-110
[ 4.598699] mmc_sdio_init_card: >>>>>>>>>>> ERR !!!
[ 4.598711] wckj ######### mmc_attach_sdio >> mmc_sdio_init_card ERR !!!
[ 4.598725] mmc1: error -110 whilst initialising SDIO card
[ 4.598738] wckj >>>>> POWER OFF <<<<<<<<< mmc_pwrseq_simple_power_off
[ 4.599894] wckj >>>>>>>>>>>>>>>>> mmc1: mmc_rescan_try_freq: trying to init card at 200000 Hz
[ 4.599924] wckj >>>>> PRE POWER ON <<<<<<<<< mmc_pwrseq_simple_pre_power_on
[ 4.599946] wckj >>>>>>>>>>>> (mmc1) Initial signal voltage of 3.3v
[ 4.607354] e2fsck: e2fsck 1.45.4 (23-Sep-2019)
[ 4.611270] wckj >>>>> POST POWER ON <<<<<<<<< mmc_pwrseq_simple_post_power_on
[ 4.613522] e2fsck: Pass 1: Checking inodes, blocks, and sizes
[ 4.617157] e2fsck: Pass 2: Checking directory structure
[ 4.618889] e2fsck: Pass 3: Checking directory connectivity
[ 4.619152] e2fsck: Pass 4: Checking reference counts
[ 4.627046] e2fsck: Pass 5: Checking group summary information
[ 4.639098] e2fsck: /dev/block/by-name/cache: 38/98304 files (0.0% non-contiguous), 7668/98304 blocks
[ 4.645614] EXT4-fs (mmcblk2p10): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
[ 4.780113] wait_for_keymaster: Waiting for Keymaster device
[ 4.836926] wckj >>>>>>>>>>>>>>> mmc_attach_sdio
[ 4.837207] wckj >>>>>>>>>>>>>>> mmc_attach_sdio (1145)
[ 4.837223] wckj start: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (0x5:0x0)
[ 4.837600] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0)
[ 4.837629] wckj stop: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (rocr: 0x30ff8000)
[ 4.837637] wckj ###########(mmc1) ocr: 0x30ff8000
[ 4.837644] wckj ###### ocr: 30ff8000 ocr->avail: 300000
[ 4.837650] wckj ######### mmc_attach_sdio >> mmc_select_voltage SUCC(0x200000) !!!
[ 4.837656] wckj >>>>>>>>>>> mmc_sdio_init_card (orc: 0x200000) ##### start
[ 4.837662] (null): >>>> retries: 18874368 ocr: 0x0 alive: 0xb
[ 4.837668] wckj start: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (0x5:0x1200000)
[ 4.838035] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 4.838060] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 4.840251] HidlServiceManagement: getService: Trying again for android.hardware.keymaster@4.0::IKeymasterDevice/default...
[ 4.849029] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 4.849060] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 4.879199] wait_for_keymaster: List of Keymaster HALs found:
[ 4.879590] wait_for_keymaster: Keymaster HAL #1: OpteeKeymasterDevice from Rockchip SecurityLevel: TRUSTED_ENVIRONMENT HAL: android.hardware.keymaster@4.1::IKeymasterDevice/default
[ 4.880571] wait_for_keymaster: Using OpteeKeymasterDevice from Rockchip for encryption. Security level: TRUSTED_ENVIRONMENT, HAL: android.hardware.keymaster@4.1::IKeymasterDevice/default
[ 4.880644] wait_for_keymaster: Keymaster device ready
[ 4.884971] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 4.884997] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 4.985431] fsck.f2fs: Info: Fix the reported corruption.
[ 4.986603] fsck.f2fs: Info: No support kernel version!
[ 4.986740] fsck.f2fs: Info: Segments per section = 1
[ 4.986802] fsck.f2fs: Info: Sections per zone = 1
[ 4.986851] fsck.f2fs: Info: sector size = 4096
[ 4.986900] fsck.f2fs: Info: total sectors = 2990584 (11681 MB)
[ 4.987844] fsck.f2fs: Info: MKFS version
[ 4.987879] fsck.f2fs: "4.19.219 #89 SMP PREEMPT Sat Jul 2 00:05:59 CST 2022"
[ 4.987897] fsck.f2fs: Info: FSCK version
[ 4.987907] fsck.f2fs: from "4.19.219 #89 SMP PREEMPT Sat Jul 2 00:05:59 CST 2022"
[ 4.994851] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 4.994876] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 6.039339] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 6.039376] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 6.051174] wckj stop: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (rocr: 0x30ff8000)
[ 6.051209] wckj $$$$$$$$$$$$$$$$$ mmc_sdio_init_card: mmc_send_io_op_cond() err=-110
[ 6.051219] mmc_sdio_init_card: >>>>>>>>>>> ERR !!!
[ 6.051231] wckj ######### mmc_attach_sdio >> mmc_sdio_init_card ERR !!!
[ 6.051242] mmc1: error -110 whilst initialising SDIO card
[ 6.051253] wckj >>>>> POWER OFF <<<<<<<<< mmc_pwrseq_simple_power_off
[ 6.052588] wckj >>>>>>>>>>>>>>>>> mmc1: mmc_rescan_try_freq: trying to init card at 100000 Hz
[ 6.052627] wckj >>>>> PRE POWER ON <<<<<<<<< mmc_pwrseq_simple_pre_power_on
[ 6.052651] wckj >>>>>>>>>>>> (mmc1) Initial signal voltage of 3.3v
[ 6.064548] wckj >>>>> POST POWER ON <<<<<<<<< mmc_pwrseq_simple_post_power_on
[ 6.288257] wckj >>>>>>>>>>>>>>> mmc_attach_sdio
[ 6.288292] wckj >>>>>>>>>>>>>>> mmc_attach_sdio (1145)
[ 6.288300] wckj start: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (0x5:0x0)
[ 6.288664] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0)
[ 6.288684] wckj stop: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (rocr: 0x30ff8000)
[ 6.288691] wckj ###########(mmc1) ocr: 0x30ff8000
[ 6.288696] wckj ###### ocr: 30ff8000 ocr->avail: 300000
[ 6.288702] wckj ######### mmc_attach_sdio >> mmc_select_voltage SUCC(0x200000) !!!
[ 6.288708] wckj >>>>>>>>>>> mmc_sdio_init_card (orc: 0x200000) ##### start
[ 6.288713] (null): >>>> retries: 18874368 ocr: 0x0 alive: 0xb
[ 6.288719] wckj start: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (0x5:0x1200000)
[ 6.289085] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 6.289107] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 6.318786] healthd: BatteryPresentPath not found
[ 6.318816] healthd: BatteryTechnologyPath not found
[ 6.318847] healthd: BatteryCycleCountPath not found
[ 6.339491] healthd: battery l=66 v=3888 t=18.8 h=2 st=2 c=1000000 fc=5000000 chg=au
[ 6.341175] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 6.341209] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 6.354180] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 6.698583] file system registered
[ 6.701755] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 6.701780] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 6.704149] using random self ethernet address
[ 6.704178] using random host ethernet address
[ 6.715069] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 6.715092] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 6.770648] wckj >>>>>>>>>>>>>>> dhd_module_init: in Dongle Host Driver, version 1.579.77.41.22 (r-20191105-2)(20191120-1)
[ 6.770683] ======== dhd_wlan_init_plat_data ========
[ 6.770695] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[ 6.770765] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=93, oob_irq_flags=0x414
[ 6.770777] dhd_wlan_init_gpio: WL_REG_ON=-1
[ 6.770792] dhd_wifi_platform_load: Enter
[ 6.770805] Power-up adapter 'DHD generic adapter'
[ 6.771225] wifi_platform_set_power = 1
[ 6.771242] ======== PULL WL_REG_ON(-1) HIGH! ========
[ 6.771248] [WLAN_RFKILL]: wckj >>>>>>>>>>>> rockchip_wifi_power: 1
[ 6.771254] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 6.771260] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[ 7.102683] wifi_platform_bus_enumerate device present 1
[ 7.102705] ======== Card detection to detect SDIO card! ========
[ 7.102712] mmc1:mmc host rescan start!
[ 7.111677] wckj >>>>>> mmc_send_io_op_cond for 2 (ocr == 0x1200000)
[ 7.111700] wckj >>>>>> mmc_send_io_op_cond (0) for 4.1 (resp: 0x30ff8000)
[ 7.651180] wckj stop: mmc_send_io_op_cond >>>>>>>>>> mmc_send_io_op_cond (rocr: 0x30ff8000)
[ 7.651216] wckj $$$$$$$$$$$$$$$$$ mmc_sdio_init_card: mmc_send_io_op_cond() err=-110
[ 7.651386] mmc_sdio_init_card: >>>>>>>>>>> ERR !!!
[ 7.651404] wckj ######### mmc_attach_sdio >> mmc_sdio_init_card ERR !!!
[ 7.651421] mmc1: error -110 whilst initialising SDIO card
[ 7.651430] wckj >>>>> POWER OFF <<<<<<<<< mmc_pwrseq_simple_power_off
[ 9.161237] failed to power up DHD generic adapter, 1 retry left
[ 9.176941] wifi_platform_set_power = 0
[ 9.176968] ======== PULL WL_REG_ON(-1) LOW! ========
[ 9.176975] [WLAN_RFKILL]: wckj >>>>>>>>>>>> rockchip_wifi_power: 0
[ 9.176982] wckj >>>>> POWER OFF <<<<<<<<< mmc_pwrseq_simple_power_off
[ 9.177004] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 9.177011] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1]
[ 9.177017] wifi_platform_bus_enumerate device present 0
[ 9.177021] ======== Card detection to remove SDIO card! ========
[ 9.177027] mmc1:mmc host rescan start!
[ 9.177100] wifi_platform_set_power = 1
[ 9.177107] ======== PULL WL_REG_ON(-1) HIGH! ========
[ 9.177112] [WLAN_RFKILL]: wckj >>>>>>>>>>>> rockchip_wifi_power: 1
[ 9.177117] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 9.177122] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
[ 9.484507] wifi_platform_bus_enumerate device present 1
[ 9.484540] ======== Card detection to detect SDIO card! ========
[ 9.484548] mmc1:mmc host rescan start!
[ 9.654733] init: Control message: Processed ctl.start for 'bootanim' from pid: 167 (/system/bin/surfaceflinger)
[ 10.001715] Freeing drm_logo memory: 732K
[ 11.507833] failed to power up DHD generic adapter, 0 retry left
[ 11.524047] wifi_platform_set_power = 0
[ 11.524077] ======== PULL WL_REG_ON(-1) LOW! ========
[ 11.524084] [WLAN_RFKILL]: wckj >>>>>>>>>>>> rockchip_wifi_power: 0
[ 11.524089] wckj >>>>> POWER OFF <<<<<<<<< mmc_pwrseq_simple_power_off
[ 11.524101] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
[ 11.524106] [WLAN_RFKILL]: wifi shut off power [GPIO-1-1]
[ 11.524112] wifi_platform_bus_enumerate device present 0
[ 11.524117] ======== Card detection to remove SDIO card! ========
[ 11.524129] mmc1:mmc host rescan start!
[ 11.524138] failed to power up DHD generic adapter, max retry reached**
[ 11.524148] unregister wifi platform drivers
[ 11.524156] wifi_platform_bus_enumerate device present 0
[ 11.524163] ======== Card detection to remove SDIO card! ========
[ 11.524172] mmc1:mmc host rescan start!
[ 11.524181] ======== dhd_wlan_deinit_plat_data ========
[ 11.524191] dhd_module_init: Failed to load the driver, try cnt 0
[ 11.524259] dhd_module_init: Failed to load driver max retry reached**
[ 11.524270] wckj >>>>>>>>>>>>> dhd_module_init: Exit err=-19
看起来是不是驱动加载问题
重新安装驱动试试
是不是这个原因
看起来像是驱动没加载成功
1、DTS配置是否正确
2、驱动有没有编译进去，是编译成ko加载还是直接启动加载
3、firmware文件是否加载成功 bin和txt文件
一般这几个配置正确了wifi驱动就加载成功了