报错的信息显示：VALUE_wendu' was not declared in this scope
C:\Users\h1525\Desktop\samrt_home_sysytem-master\arduino_control\arduino_control.ino: In function 'void loop()':
arduino_control:179:19: error: 'VALUE_wendu' was not declared in this scope
myGizwits.write(VALUE_wendu, varW_wendu);
^
arduino_control:184:19: error: 'VALUE_shidu' was not declared in this scope
myGizwits.write(VALUE_shidu, varW_shidu);
^
arduino_control:187:27: error: 'EVENT_LED_OnOff' was not declared in this scope
if(myGizwits.hasBeenSet(EVENT_LED_OnOff))
^
arduino_control:207:27: error: 'EVENT_tiaoguang' was not declared in this scope
if(myGizwits.hasBeenSet(EVENT_tiaoguang))
^
arduino_control:218:27: error: 'EVENT_reshiuqi' was not declared in this scope
if(myGizwits.hasBeenSet(EVENT_reshiuqi))
^
arduino_control:257:27: error: 'EVENT_chuang' was not declared in this scope
if(myGizwits.hasBeenSet(EVENT_chuang))//窗户
^
使用库 Gizwits 在文件夹： E:\Arduino\libraries\Gizwits (legacy)
使用 1.0 版本的库 Wire 在文件夹： E:\Arduino\hardware\arduino\avr\libraries\Wire
使用 1.0 版本的库 SoftwareSerial 在文件夹： E:\Arduino\hardware\arduino\avr\libraries\SoftwareSerial
使用 1.1.3 版本的库 Servo 在文件夹： E:\Arduino\libraries\Servo
使用库 dht11 在文件夹： E:\Arduino\libraries\dht11 (legacy)
使用 2.28.10 版本的库 U8g2 在文件夹： C:\Users\h1525\Documents\Arduino\libraries\U8g2
使用 1.0 版本的库 SPI 在文件夹： E:\Arduino\hardware\arduino\avr\libraries\SPI
exit status 1
'VALUE_wendu' was not declared in this scope
代码段：
#include <Arduino.h>//Arduino库
#include <Gizwits.h>//机智云库
#include <Wire.h>
#include <SoftwareSerial.h>//软串口
#include <Servo.h>//舵机
#include <dht11.h>//温湿度
#include <U8x8lib.h>//OLED
#ifdef U8X8_HAVE_HW_SPI
#include <SPI.h>
#endif
#include "voice.h"//语音播报
#include "function_test.h" //功能函数
SoftwareSerial mySerial(13,4); //给蓝牙HC-05使用的串口，RX ,TX = 13,4
//Servo myservo; //控制门的舵机
//Servo windowservo; //控制窗户的舵机
Gizwits myGizwits;
dht11 DHT11;
int pos = 0; // 初始化舵机位置
//int smokepin = 2; //烟雾报警器
//int fanpin = 6; //净化器
//int fengminqipin = 7;//蜂鸣器
//int myledPin = 8; // 客厅灯
//int servopin = 9; //门servo舵机
//int windowservopin = 12; //窗servo舵机
//int hotwaterpin = 10;//热水器
//int pwmpin =11; //卧室灯
bool varR_LED_OnOff = 0;
bool varR_jinghuaqi = 0;
#define KEY1 6
#define KEY2 7
#define KEY1_SHORT_PRESS 1
#define KEY1_LONG_PRESS 2
#define KEY2_SHORT_PRESS 4
#define KEY2_LONG_PRESS 8
#define NO_KEY 0
#define KEY_LONG_TIMER 3
#define DHT11PIN A0 //读取A0温湿度
U8X8_SSD1306_128X64_NONAME_SW_I2C u8x8(/* clock=*/ SCL, /* data=*/ SDA, /* reset=*/ U8X8_PIN_NONE);
//int flag =0;
unsigned long Last_KeyTime = 0;
unsigned long gokit_time_s(void)
{
return millis() / 1000;
}
//温湿度传感器
double Fahrenheit(double celsius)
{
return 1.8 * celsius + 32;
} //摄氏温度度转化为华氏温度
double Kelvin(double celsius)
{
return celsius + 273.15;
} //摄氏温度转化为开氏温度
// 露点（点在此温度时，空气饱和并产生露珠）
// 参考: http://wahiduddin.net/calc/density_algorithms.htm
double dewPoint(double celsius, double humidity)
{
double A0= 373.15/(273.15 + celsius);
double SUM = -7.90298 * (A0-1);
SUM += 5.02808 * log10(A0);
SUM += -1.3816e-7 * (pow(10, (11.344*(1-1/A0)))-1) ;
SUM += 8.1328e-3 * (pow(10,(-3.49149*(A0-1)))-1) ;
SUM += log10(1013.246);
double VP = pow(10, SUM-3) * humidity;
double T = log(VP/0.61078); // temp var
return (241.88 * T) / (17.558-T);
}
// 快速计算露点，速度是5倍dewPoint()
// 参考: http://en.wikipedia.org/wiki/Dew_point
double dewPointFast(double celsius, double humidity)
{
double a = 17.271;
double b = 237.7;
double temp = (a * celsius) / (b + celsius) + log(humidity/100);
double Td = (b * temp) / (a - temp);
return Td;
}
//初始化
void setup() {
Serial.begin(9600); //esp-8266
mySerial.begin(9600); // hc-05
myservo.attach(servopin); //门舵机控制9
myservo.write(0); //初始化门舵机
windowservo.attach(windowservopin); //窗户舵机控制12
windowservo.write(0);
pinMode(KEY1, INPUT_PULLUP);
pinMode(KEY2, INPUT_PULLUP);
pinMode(A0,INPUT);//A0 温湿度传感器
pinMode(smokepin,INPUT);//2 火灾报警
pinMode(fanpin,OUTPUT);//6 净化器
pinMode(fengminqipin,OUTPUT);//7 蜂鸣器
pinMode(myledPin,OUTPUT);// 8 客厅灯
pinMode(hotwaterpin,OUTPUT);//10 热水器
pinMode(pwmpin,OUTPUT);//11 卧室灯
myGizwits.begin();
begin();
}
//OLED显示
void begin ()
{
u8x8.begin();
u8x8.setPowerSave(0);
u8x8.setFont(u8x8_font_chroma48medium8_r);
u8x8.drawString(3,1,"SMART-HOME");
u8x8.drawString(0,2,"Temp :");
u8x8.drawString(0,3,"Hum :");
u8x8.drawString(0,4,"Pwm :");
u8x8.drawString(0,5,"Fire :");
u8x8.drawString(0,6,"Danli's Home");
}
//Wifi配网
void wifiStatusHandle()
{
if(myGizwits.wifiHasBeenSet(WIFI_CON_ROUTER)){}
}
int ketingdeng=1;
int reshuiqi=1;
int jinghuaqi=1;
int chuang=1;
//主函数
void loop() {
while(mySerial.available()) //如果串口可用
{ char c;
c=mySerial.read();
mySerial.println (c);
switch(c){
case '1':servo_init();
break;
case '2':open_the_door();
break;
case '3':close_the_door();
break;
}
}
//烟雾报警
unsigned long varW_fire = 0;
if(digitalRead(smokepin))//安全是高电平
{
u8x8.setCursor(6,5);
u8x8.print("Safe");
fengmingqi_close();
attachInterrupt(digitalPinToInterrupt(2), fan_open,CHANGE); //中断函数
}
else
{
u8x8.setCursor(6,5);
u8x8.print("Fire");
fengmingqi_open();
attachInterrupt(digitalPinToInterrupt(2), fan_close,CHANGE); //中断函数
delay(1000);
fengmingqi_close();
}
//温湿度OLED显示
int chk = DHT11.read(DHT11PIN);
unsigned long varW_wendu = (float)DHT11.temperature ;
u8x8.setCursor(6,2);//这里设置显示的坐标
u8x8.print(varW_wendu);//输出显示内容
myGizwits.write(VALUE_wendu, varW_wendu);
unsigned long varW_shidu = (float)DHT11.humidity ;
u8x8.setCursor(6,3);//这里设置显示的坐标
u8x8.print(varW_shidu);//输出显示内容
myGizwits.write(VALUE_shidu, varW_shidu);
//客厅灯
if(myGizwits.hasBeenSet(EVENT_LED_OnOff))
{
myGizwits.read(EVENT_LED_OnOff,&varR_LED_OnOff);
if(ketingdeng==varR_LED_OnOff)
{
if(varR_LED_OnOff==1)
{
myled_open();
}
else
{
myled_close();
}
ketingdeng=!varR_LED_OnOff;
}
}
//卧室灯
unsigned long varR_tiaoguang = 0;
if(myGizwits.hasBeenSet(EVENT_tiaoguang))
{
myGizwits.read(EVENT_tiaoguang,&varR_tiaoguang);//读取pwm值
analogWrite(pwmpin,varR_tiaoguang); //把读取的值写入机智云中间变量
u8x8.setCursor(6,4);//这里设置显示的坐标
u8x8.print(varR_tiaoguang);//输出显示内容
}
//热水器
bool varR_reshuiqi = 0;
if(myGizwits.hasBeenSet(EVENT_reshiuqi))
{
myGizwits.read(EVENT_reshiuqi,&varR_reshuiqi);//Address for storing data
if(reshuiqi==varR_reshuiqi)
{
if(varR_reshuiqi==1)
{
hotwater_open();
}
else
{
hotwater_close();
}
reshuiqi=!varR_reshuiqi;
}
}
//净化器
if(myGizwits.hasBeenSet(EVENT_jinhuaqi))
{
myGizwits.read(EVENT_jinhuaqi,&varR_jinghuaqi);
if(jinghuaqi==varR_jinghuaqi)
{
if(varR_jinghuaqi==1)
{
fan_open();
speak_open_fan();
}
else
{
fan_close();
speak_close_fan();
}
jinghuaqi=!varR_jinghuaqi;
}
}
//窗户
bool varR_chuang = 0;
if(myGizwits.hasBeenSet(EVENT_chuang))//窗户
{
myGizwits.read(EVENT_chuang,&varR_chuang);
if(chuang==varR_chuang)
{
if(varR_chuang==1)
{
window_open();
}
else
{
window_close();
}
chuang=!varR_chuang;
}
}
wifiStatusHandle();//WIFI Status Handle
myGizwits.process();
}
我前面也有定义头文件什么的，但是还是报错。
请问问题解决了吗
请问解决了吗？