分别在什么时候用 #define 和 enum?

看 stm32 官方的库函数源码,配置外设属性时有时采用 define,有时采用 enum,比如配置 GPIO 时,配置上拉/下拉就用的 enum:

/**
 * @brief  GPIO Configuration PullUp PullDown enumeration
 */
typedef enum
{
  GPIO_PuPd_NOPULL = 0x00,
  GPIO_PuPd_UP     = 0x01,
  GPIO_PuPd_DOWN   = 0x02
}GPIOPuPd_TypeDef;
#define IS_GPIO_PUPD(PUPD) (((PUPD) == GPIO_PuPd_NOPULL) || ((PUPD) == (GPIO_PuPd_Up) || ((PUPD) == GPIO_PuPd_DOWN))

而在配置引脚时用的是 define:

/** @defgroup GPIO_pins_define 
  * @{
  */ 
#define GPIO_Pin_0                 ((uint16_t)0x0001)  /* Pin 0 selected */
#define GPIO_Pin_1                 ((uint16_t)0x0002)  /* Pin 1 selected */
#define GPIO_Pin_2                 ((uint16_t)0x0004)  /* Pin 2 selected */
#define GPIO_Pin_3                 ((uint16_t)0x0008)  /* Pin 3 selected */
#define GPIO_Pin_4                 ((uint16_t)0x0010)  /* Pin 4 selected */
#define GPIO_Pin_5                 ((uint16_t)0x0020)  /* Pin 5 selected */
#define GPIO_Pin_6                 ((uint16_t)0x0040)  /* Pin 6 selected */
#define GPIO_Pin_7                 ((uint16_t)0x0080)  /* Pin 7 selected */
#define GPIO_Pin_8                 ((uint16_t)0x0100)  /* Pin 8 selected */
#define GPIO_Pin_9                 ((uint16_t)0x0200)  /* Pin 9 selected */
#define GPIO_Pin_10                ((uint16_t)0x0400)  /* Pin 10 selected */
#define GPIO_Pin_11                ((uint16_t)0x0800)  /* Pin 11 selected */
#define GPIO_Pin_12                ((uint16_t)0x1000)  /* Pin 12 selected */
#define GPIO_Pin_13                ((uint16_t)0x2000)  /* Pin 13 selected */
#define GPIO_Pin_14                ((uint16_t)0x4000)  /* Pin 14 selected */
#define GPIO_Pin_15                ((uint16_t)0x8000)  /* Pin 15 selected */
#define GPIO_Pin_All               ((uint16_t)0xFFFF)  /* All pins selected */

#define IS_GPIO_PIN(PIN) ((((PIN) & (uint16_t)0x00) == 0x00) && ((PIN) != (uint16_t)0x00))
#define IS_GET_GPIO_PIN(PIN) (((PIN) == GPIO_Pin_0) || \
                              ((PIN) == GPIO_Pin_1) || \
                              ((PIN) == GPIO_Pin_2) || \
                              ((PIN) == GPIO_Pin_3) || \
                              ((PIN) == GPIO_Pin_4) || \
                              ((PIN) == GPIO_Pin_5) || \
                              ((PIN) == GPIO_Pin_6) || \
                              ((PIN) == GPIO_Pin_7) || \
                              ((PIN) == GPIO_Pin_8) || \
                              ((PIN) == GPIO_Pin_9) || \
                              ((PIN) == GPIO_Pin_10) || \
                              ((PIN) == GPIO_Pin_11) || \
                              ((PIN) == GPIO_Pin_12) || \
                              ((PIN) == GPIO_Pin_13) || \
                              ((PIN) == GPIO_Pin_14) || \
                              ((PIN) == GPIO_Pin_15))
/**
  * @}
  */ 

PuPd 和 GPIO_Pin 都是 GPIO_InitTypeDef 的成员,为什么会用这两种不同的方式来配置?他们之间有什么区别吗?下面列出 GPIO_InitTypeDef 的定义。

/** 
  * @brief   GPIO Init structure definition  
  */ 
typedef struct
{
  uint32_t GPIO_Pin;              /*!< Specifies the GPIO pins to be configured.
                                       This parameter can be any value of @ref GPIO_pins_define */

  GPIOMode_TypeDef GPIO_Mode;     /*!< Specifies the operating mode for the selected pins.
                                       This parameter can be a value of @ref GPIOMode_TypeDef */

  GPIOSpeed_TypeDef GPIO_Speed;   /*!< Specifies the speed for the selected pins.
                                       This parameter can be a value of @ref GPIOSpeed_TypeDef */

  GPIOOType_TypeDef GPIO_OType;   /*!< Specifies the operating output type for the selected pins.
                                       This parameter can be a value of @ref GPIOOType_TypeDef */

  GPIOPuPd_TypeDef GPIO_PuPd;     /*!< Specifies the operating Pull-up/Pull down for the selected pins.
                                       This parameter can be a value of @ref GPIOPuPd_TypeDef */
}GPIO_InitTypeDef;

高效率,需要跨二进制版本兼容(比如跨库给别的程序调用)的,用define
程序内部使用,用enum